Clik here to view.
Source NAT through VPN not working from switched interface
Hi There, I'm currently trying to solve an AWS transitive routing issue using a VPN between two SRX devices, coming from a Cisco world, this has been a bit of a learning curve this week - I've made...
View ArticleI have a problem with ip-monitoring and rpm in fail-over route default
Hi. I have a configuration for failover route default with RPM and IP-Monitoring.My configuration is: show configuration services rpm | display set set services rpm probe PRIN test test-8.8.8.8 target...
View ArticlePeer proposed phase2 proposal conflicts with local configuration. Negotiation...
hi guys,i've created a site2site vpn between our srx340 running junos 17.3R1.10 and an SOPHOS ASG.3 subnets on my side and on on the other side all defined with Traffic Selectors. Tunnel comes up fine...
View ArticleSRX 1400 is blocking packets for download during Debian Distribution...
Dear Juniper experts, I am facing an issue with SRX 1400, Network diagram is attached to understand the scenario. Problem: Any end user who has his gateway on SRX 1400 is unable to download debian...
View ArticleDHCP relay Issue
Forgive me here I am new to Junos but I believe I have created a network that is vlaned and is inter vlan routed but I cannot relay DHCP requests to a server. Attached is my config can anyone give me...
View ArticleStatic routes with RPM
Hi everyone,This is I am trying to accomplish: SRX f1-199.199.199.1/30-( PROVIDER A SWITCHED NETWORK)-199.199.199.2/30 PE f2-200.200.200.1/30-(PROVIDER B SWITCHED NETWORK)-200.200.200.2/30 PEWe...
View ArticleWhen SRX is both FHR/LHR
Hi everyone,This is my undertanding:PIM SPARSE , PIM SPARSE- DENSE/ PIM DENSE mode all refer to how PIM enbaled router deals with sending multicast stream towards PIM neighbor; For Dense, the logic is...
View Articleusp_ipc_client_reconnect messages in syslog
Hi, I have a cluster on the SRX 3600. RG0 and RG1 active on different nodes.In syslog began to appear messagesFW-node1 node1.fpc7.pic0 usp_ipc_client_reconnect: failed to connect to the server:...
View ArticleSRX with packet mode , RSVP bandwidth management ?
Hi all, Can RSVP help in the scenario where if the SRX interconnect via Microwave link , when primary microwave link bandwidth is downgrade from 100mbps to 20 mbps , can the RSVP detect the congestion...
View ArticlePPPoE problems
Tring to connect to ISP over ADSl. I am able to establish a session and see packets flowing but no IP address is assigned to the interface a LCP is down. The ISP should assign IP by DHCP. Not...
View ArticleClik here to view.
NAT VLAN trunk directly to untrust statics?
I'm trying to NAT off a VLAN trunk directly to public static interface on an SRX-345, is that possible? Do I have to create ge-0/0/0.0 and ge-0/0/0.1 etc for each subnet or something like that, and can...
View ArticleRedundant ISP
Default router is the SRX. If the ISP goes down I want the default route to change on the router to an alternate router? The primary router and default-gateway for the network is the SRX at...
View ArticleFirewall filter configuration for loopback IP access
Hi, Our ISP want to monitor SRX(MPLS mode) loopback IP(Provided by ISP) from below given IP subnet.ISP has shared below Cisco router configuration and request us to configure the same on SRX....
View ArticleSignificant SRX reliability problems
Generally speaking, I really like working with the SRX. We use 210, 220, and 240 models throughout the company. It's trivially easy to set up tunnels with OSPF to do all kinds of neat inter-office...
View ArticleSRX100H2 Factory Reset Help Required
I have 2 SRX100H2 devices that were somehow locked and cannot be factory defaulted or changed in any way. I need assistance trying to set them back to factory default and enable jWEB.What I have done:I...
View ArticleWhat the main reason when have "error bad UDP checksum" ?
Hi all, currently we facing and issue when the snmp server cannot poling the certain interface info on other MX router. The traffic is flow through SRX5800 before it reach the MX router. When do tcp...
View ArticleSRX real lab with ability to ping from win10 machine
hey, was looking to set up a real lab with routers and switches where i could ping from a windows 10 machine and also use wireshark to learning purposes. i was thinking about buying a 4 port PCIe card...
View ArticleEvent option and change of config
HI everyone, I want SRX 100 to do this:If RPM for 10.10.10.1 fails, install static route 8.8.8.8/32 next hop 10.10.10.2 using EVENT -OPTION SET UP: SRX 10.10.10.6----SW-----10.10.10.1F1 R1...
View ArticleShow chassis routing-engine command
Hi everyone When we use the command show below, we see " USER" , what does USER mean below?user@host> show chassis routing-engineRouting Engine status: Temperature 38 degrees C / 100 degrees F CPU...
View ArticleSRX Per-unit-scheduling
I am having a bit of trouble replicating some orginal cisco qos configuration. I am in routed mode on the SRX. In summary, I have a physical wan interface with multiple dot1q sub-interfaces which are...
View Article