Hey community,
because there ist no warranty or no active support for my SRX100H I need your help.
I wanted to upgrade my SRX to 12.1X46. Everythings looks good but after reboot I get the messages:
can't load '/kernel'
can't load '/kernel.old'
Try to install from loader prompt via usb or tftp fails too. For usb I get the following message:
loader> install file:///junos-srxsme-12.1X46-D60.4-domestic.tgz
Target device selected for installation: internal media
cannot open package (error 22)
As I read this error means that no usb device is connected. I tested 5 different usb sticks, no luck!
For tftp I get this:
loader> install tftp://192.168.0.2/junos-srxsme-12.1X46-D60.4-domestic.tgz
Target device selected for installation: internal media
octeth0: Up 1000 Mbps Full duplex (port 0)
/kernel data=0xb16cdc+0x134b2c syms=[0x4+0x8bbd0+0x4+0xcadc3]
Kernel entry at 0x801000e0 ...
init regular console
Primary ICache: Sets 64 Size 128 Asso 4
Primary DCache: Sets 1 Size 128 Asso 64
Secondary DCache: Sets 128 Size 128 Asso 8
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
kld_map_v: 0x8ff80000, kld_map_p: 0x0
Copyright (c) 1996-2016, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 12.1X46-D60.4 #0: 2016-10-12 17:11:44 UTC
builder@quoarth.juniper.net:/volume/build/junos/12.1/service/12.1X46-D60.4/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel
JUNOS 12.1X46-D60.4 #0: 2016-10-12 17:11:44 UTC
builder@quoarth.juniper.net:/volume/build/junos/12.1/service/12.1X46-D60.4/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel
real memory = 1073741824 (1024MB)
avail memory = 559992832 (534MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
Security policy loaded: JUNOS MAC/pcap (mac_pcap)
Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot)
netisr_init: !debug_mpsafenet, forcing maxthreads from 2 to 1
cpu0 on motherboard
: CAVIUM's OCTEON 5020 CPU Rev. 0.1 with no FPU implemented
L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way.
L2 Cache: Size 128kb, 8 way
obio0 on motherboard
uart0: <Octeon-16550 channel 0> on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
dwc0: <Synopsis DWC OTG Controller Driver> on obio0
usb0: <USB Bus for DWC OTG Controller> on dwc0
usb0: USB revision 2.0
uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1: vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2
uhub1: single transaction translator
uhub1: 2 ports with 1 removable, self powered
cpld0 on obio0
pcib0: <Cavium on-chip PCI bridge> on obio0
Disabling Octeon big bar support
PCI Status: PCI 32-bit: 0xc041b
pcib0: Initialized controller
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 2.0 (no driver attached)
pci0: <serial bus, USB> at device 2.1 (no driver attached)
pci0: <serial bus, USB> at device 2.2 (no driver attached)
gblmem0 on obio0
octpkt0: <Octeon RGMII> on obio0
cfi0: <AMD/Fujitsu - 4MB> on obio0
octpkt_attach: Initializing octpkt0 interface
Timecounter "mips" frequency 500000000 Hz quality 0
###PCB Group initialized for udppcbgroup
###PCB Group initialized for tcppcbgroup
md0: Preloaded image </isofs-install-srxsme> 10022912 bytes at 0x80ea21a4
Trying to mount root from cd9660:/dev/md0
WARNING: preposterous time in file system
WARNING: clock 10710 days greater than file system time
tty: not found
Starting JUNOS installation:
Source Package: net0:/junos-srxsme-12.1X46-D60.4-domestic.tgz
Target Media : internal
Product : srx100h
ERROR: Target media /dev/da0 does not exist
I think the flash device is crashed. Is there a way to solve this?
Thanks for your reply!