Hello,
We are installing a new SRX5600 and we are looking that some interface 10G are not working. [ALL SFP are Juniper]
Looking the outpower output and there is nothing:
show interfaces diagnostics optics xe-3/0/1
Physical interface: xe-3/0/1
Laser bias current : 0.000 mA
Laser output power : 0.0000 mW / - Inf dBm
Module temperature : 18 degrees C / 65 degrees F
Module voltage : 3.3390 V
Receiver signal average optical power : 0.0000 mW / - Inf dBm
Laser bias current high alarm : Off
Laser bias current low alarm : On
Laser bias current high warning : Off
Laser bias current low warning : On
Laser output power high alarm : Off
Laser output power low alarm : On
Laser output power high warning : Off
Laser output power low warning : On
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : On
Laser rx power high warning : Off
Laser rx power low warning : On
Laser bias current high alarm threshold : 95.000 mA
Laser bias current low alarm threshold : 3.000 mA
Laser bias current high warning threshold : 90.000 mA
------------------------------------------------------------------------------------------
This is the hardware installed:
show chassis hardware
FPC 3 REV 09 750-061262 CAHZ1366 SRX5k IOC II
CPU REV 03 711-061263 CAJA9651 SRX5k MPC PMB
MIC 0 REV 11 750-049488 CAJA0871 10x 10GE SFP+
PIC 0 BUILTIN BUILTIN 10x 10GE SFP+
Xcvr 1 REV 01 740-021309 H3P2004895 SFP+-10G-LR
Xcvr 2 REV 01 740-021309 H3P2004630 SFP+-10G-LR
MIC 1 REV 07 750-055732 CAHX9529 20x 1GE(LAN) SFP
PIC 2 BUILTIN BUILTIN 10x 1GE(LAN) SFP
Xcvr 0 REV 02 740-011613 AM16382KQAM SFP-SX
Xcvr 1 REV 02 740-011613 AM16382KQA9 SFP-SX
PIC 3 BUILTIN BUILTIN 10x 1GE(LAN) SFP
Xcvr 0 REV 02 740-013111 H114328 SFP-T
Xcvr 1 REV 02 740-011613 AM16382KPGU SFP-SX
Xcvr 2 REV 02 740-011613 AM16382KQBB SFP-SX
Xcvr 6 REV 02 740-013111 H124469 SFP-T
Xcvr 7 REV 02 740-013111 H111051 SFP-T
Xcvr 8 REV 02 740-013111 H110681 SFP-T
Xcvr 9 REV 02 740-013111 H113404 SFP-T
-----------------------------------------------------------------------
The status of the port:
root@ROFW02> show interfaces xe-3/0/2 brief
Physical interface: xe-3/0/2, Enabled, Physical link is Down
Link-level type: Ethernet, MTU: 1500, LAN-PHY mode, Speed: 10Gbps,
Loopback: None, Source filtering: Disabled, Flow control: Enabled
Device flags : Present Running Down
Interface flags: Hardware-Down SNMP-Traps Internal: 0x4000
Any idea of what could be wrong?
Thanks